B-CUBE 5-inch Flying Car FPV Drone Frame Kit Carbon Fiber Racing Quadcopter BF INAV F722 H743 F745 Flight Control Featured
Select Variant:
Selected: B-CUBE 5-inch Flying Car FPV Drone Frame Kit Carbon Fiber Racing Quadcopter BF INAV F722 H743 F745 Flight Control
默认
Default
5inch Flying Car
5inch...
Car Motor A
Car Motor A
Car Motor B
Car Motor B
Car F745 A
Car F745 A
Car F745 B
Car F745 B
Car F745 C
Car F745 C
Car H743 A
Car H743 A
Car H743 B
Car H743 B
Car H743 C
Car H743 C
F745 NO Battery
F745...
H743 NO Battery
H743...
F745 With Battery
F745...
H743 With Battery
H743...
Flying Car

B-CUBE 5-inch Flying Car FPV Drone Frame Kit Carbon Fiber Racing Quadcopter BF INAV F722 H743 F745 Flight Control

Product Name B-CUBE 5-inch Flying Car FPV Drone Frame Kit Carbon Fiber Racing Quadcopter BF INAV F722 H743 F745 Flight Control
Category Flying Car
Product ID #000337
Updated 2026-11-18

Pixracer R15 Autopilot xracer PX4  Flight Controller        

If you do not have GH1.25 3DR Power Module ,please select R15 M10S PDB Package.
Note: Pixracer must be powered by Power Module, and ESC with BEC cannot be used to power pixracer,Because the circuit board is designed like this. So please use 3DR Power Module for power supply.

R15 Tower Set Package Included:
Pixracer R15 Flight controller  x 1
Safety switcher  and Buzzer  x 1
Micro
4G TFCard  x 1

Card reader  x1
Cables set (GH1.25 6P Line+GH1.25 4P Line + GH1.25 5P Line)  x1


R15 M8N Set Package Included:
Pixracer R15 Flight controller  x 1

M8N GPS X1
Plastic  shell x 1
Safety switcher  and Buzzer  x 1
Micro
4G TFCard  x 1

Card reader  x1
Cables set (GH1.25 6P Line+GH1.25 4P Line + GH1.25 5P Line)  x1


R15 M8N PDB Set Package Included:
Pixracer R15 Flight controller  x 1

M8N GPS X1
Plastic  shell x 1
Safety switcher  and Buzzer  x 1
Micro
4G TFCard  x 1

Card reader  x1
Cables set (GH1.25 6P Line+GH1.25 4P Line + GH1.25 5P Line)  x1


The Pixracer is the common name for the FMUv4 generation of Pixhawk autopilots. It has been designed primarily for the demanding requirements of small multicopters, but of course can be used on planes and other vehicles which require no more than 6 pwm outputs for controlling escs and motors.


Many people will mistakenly believe that the PixRacer is just a standard "racer" controller that lacks many of the functionalities of a complete autopilot system. Well, don't be fooled! PixRacer has all the capabilities of the original PixHawk -including version 2- and even more! But is optimized in size and has just about the right amount of input/outputs that allows you to switch from a full enriched autopilot stack system -with autolanding and full navigation- to a high-performance racing platform. Yup, if you get tired of advanced waypoints, then flip the switch and race like a pro! R15 has an updated accelerometer/gyroscope, magnetometer and ROHS (Lead Free).


Interfaces/Connectivity

  • Wifi: ESP-01 802.11bgn Flashed with MavESP8266

  • MicroSD card reader

  • Micro USB

  • RGB LED

  • GPS (serial + I2C)

  • TELEM1/TELEM2

  • Wifi serial

  • FrSky Telemetry serial

  • Debug connector (serial + SWD)

  • Connectors: GPS+I2C, RC-IN, PPM-IN, RSSI, SBus-IN, Spektrum-IN, USART3 (TxD, RxD, CTS, RTS), USART2 (TxD, RxD, CTS, RTS), FRSky-IN, FRSky-OUT, CAN, USART8 (TxD, RxD), ESP8266 (full set), SERVO1-SERVO6, USART7 (TxD, RxD), JTAG (SWDIO, SWCLK), POWER-BRICK (VDD, Voltage, Current, GND), BUZZER-LED_BUTTON.

Power System:

5-5.5VDC from USB or PowerBrick connector. Optional/recommendedACSP4 +5V/+12V Power Supply.

Weight and Dimensions:
Weight: 10.54g (.37 oz)
Width: 36mm (1.42”)
Length: 36mm (1.42”)


Description: ​ This PM02 Power Module provides a simple way to supply regulated 5.2V to flight controller 

from the battery while providing current consumption and battery voltage measurements via analog signal

 through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, 

along with shrink tubing on the PCBA for physical protection. ​

Specification:

  • Input Voltage: 2S-12S

  • PCB Cont. Current Rating: 60A

  • PCB Burst Current Rating: 100A (<60 Sec)

  • Max Current Sensing: 120A

  • Output: DC 5.2V & 3A Max

  • Voltage Divider: 18.182

  • Amperes per Volt: 36.364 

  • Weight: 20g

MAX-M10S GPS

Specification:

The MAX-M10S module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals.

MAX-M10S supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and BeiDou). The high number of visible satellites enables the receiver to select the 

best signals. This maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. u-blox Super-S (Super-Signal) technology 

offers great RF sensitivity and can improve the dynamic position accuracy with small antennas or in non-line-of-sight scenarios.

The extremely low power consumption of 25 mW in continuous tracking mode allows great powerautonomy for all battery-operated devices, such as asset trackers, without 

compromising on GNSS performance.

For maximum sensitivity in passive antenna designs, MAX-M10S integrates an LNA followed by a SAW filter in the RF path.

MAX-M10S offers backwards pin-to-pin compatibility with products from the previous u-blox generations, which saves the designer's effort and reduces costs when upgrading 

designs to the advanced low-power u-blox M10 GNSS technology.

Performance:

100%
放大图片
滚轮缩放 · 拖拽移动 · ESC 关闭
Contact Us ×