RCtoSky LX1100 6 Axle Hexacopter
Features：
1. Simple folding parts, one-key folding, saving time and effort;
2. The super-large motor base can be built-in ESC to solve the messy wiring on the center board.
3. 2.0MM carbon fiber hollow design center board, saving time for disassembly and assembly.
4. Intelligent electric tripod, remote control one-key contraction, making the flight more beautiful.
Parameters：
Symmetrical motor wheelbase: 1100MM
Arm diameter: 25MM
LX1100 6 Axle Package can lift 10KG(use 6S or 12S Battery)
Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller
Features:
Pixhawk 2.4.8 support the latest official ardupilot firmware and PX4 firmware.
1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
Specifications:
Interface
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
PIXHAWK 6C PRO
The Pixhawk® 6C PRO is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pixhawk® 6C PRO's H7 microcontroller contain the Arm® Cortex®-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models.
The Pixhawk 6C PRO includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.
The Pixhawk® 6C PRO is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial application.
Key Design Points
High performance STM32H743 Processor with more computing power & RAM
Build-in Buzzer,Build-in RGB LED,support Independent external Safety Button,With Plastic Case
New cost-effective design with low-profile form factor
Newly designed integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs
Technical Specification
Processors & Sensors
FMU Processor: STM32H743
32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM
IO Processor: STM32F103
32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
On-board sensors
Accel/Gyro: ICM-42688-P
Accel/Gyro: BMI055
Mag: IST8310
Barometer: MS5611
Electrical data
Voltage Ratings:
Max input voltage: 6V
USB Power Input: 4.75~5.25V
Servo Rail Input: 0~36V
Current Ratings:
TELEM1 Max output current limiter: 1.5A
All other port combined output current limiter: 1.5A
Mechanical data
Dimensions: 85 * 45 * 10 mm
Weight (Plastic Case) : 33g
PIXHAWK 2.4.8 Package include:
LX1100 Full Carbon Fiber+ 6 pcs B-CUBE 80A Brushless ESC+
3 Pairs 3K Carbon Fiber Propeller 2255 + 6 PCS 6215 170KV Motor +
PIXHAWK 2.4.8(white or black shell)Flight Controller+4G TF Card+ Safety Button+Buzzer+PPM Encoder+OLED Screen+RGB LED+I2C Expansion Board+3 Line(4Pin 1.25 ,6Pin 1.25 ,3Pin 2.5.4)+M8N GPS+GPS Holder+PM02 V3.2 Power Module(support 12S) + Shock Absorber +433MHZ 1000MW Radio Telemetry V5
(If you need 915MHZ, please leave a message)
PIXHAWK 6C PRO Package include:
LX1100 Full Carbon Fiber+ 6 pcs B-CUBE 80A Brushless ESC+
3 Pairs 3K Carbon Fiber Propeller 2255 + 6 PCS 6215 170KV Motor +
PIXHAWK 6C PRO(white or black shell) + 2*PWM Module+I2C Expansion Board + RGB LED Module+Safety Button+4G TF Card+M8N GPS+GPS Holder+Shock Absorber+PM02 V3.2
Power Module(support 12S) +433MHZ 1000MW Radio Telemetry V6
(If you need 915MHZ, please leave a message)
6215 170KV Motor （Support 6S-12S）
B-CUBE-Pro-80A-HV V3 ESC
B-CUBE-Pro-80A-HV V3 for Multicopter
Specification:
Voltage: 6-14S lithium battery. Current 80A. Weight 195g
Without BEC. Without fan (no need for fan)
Power cord (red and black line) No. 12 silicone wire, length: 14cm.
Motor line (3 black lines) No. 14 silicone wire, length: 70cm
Signal line (black and white line) Length: 25cm
Shell waterproof.
Model: B-CUBE-Pro-80A-HV V3 ESC
Drive mode: BLDC
Continues Current :80A
Instantaneous Current (10 seconds) : 100A
Output lithium battery Section number : 6-14s
Parameter Programming Features: Automatic angle (High / medium)
01 Warnings
Ensure all wires and connections are well insulated before connecting the ESC to related devices, as short circuit will damage your ESC.
Ensure all devices are well connected to prevent poor connection that may cause your multi-rotor to lose control or other unpredictable issues such
as damage to the device.
Read through the manuals of all power devices and ensure the power configuration is rational before using this unit.
Please use a soldering iron (ensuring it’s connected to a GND wire) with the power of at least 60W to solder all input/output wires and connectors.
Stop using the ESC when its casing temperature exceeds 100℃, otherwise your ESC will get destroyed and may also get your motor damaged.
Please swap any two ESC-to-motor wires if the motor runs in reverse.
02 Features
Special core program for multi-rotor controllers greatly improves throttle response.
Specially optimized software for excellent compatibility with multi-rotor motors.
Microprocessor powered by independent DC regulator has better anti-interference performance greatly reduces the risk of losing control.
Separate signal wires for reminding user of RPM output & error states.
All settings except the timing are preset, making usage simple, high intelligent and adaptive.
Compatible with various flight-controller and supports a signal frequency of up to 621Hz.
DEO (Driving Efficiency Optimization) technology for better throttle linearity and higher driving efficiency.
PWM frequency of 18KHz.
3 Pairs 3K Carbon Fiber Propeller
The new propeller-type aerial dedicated full carbon paddle paddle-type three-hole installation
Using carbon content of 100% pure imported Toray carbon fiber 3K woven, high temperature and pressure precast precision machining, hardness higher than conventional products market.
Radio Telemetry V6:
Radio telemetry can be used for wireless communication between pixhawk and computer or mobile phone.
OLED Module can display some message.
PM02 Power Module
- Input Voltage: 2S-12S
- PCB Cont. Current Rating: 60A
- PCB Burst Current Rating: 100A (<60 Sec)
- Max Current Sensing: 120A
- Output: DC 5.2V & 3A Max
- Voltage Divider: 18.182
- Amperes per Volt: 36.364
This PM02 Power Module provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.
